QQ登录

只需一步,快速开始

用微信登录

扫一扫,用微信登录

手机号码,快捷登录

查看: 1648|回复: 0

[技术分享] 【博皓干货】Why Do New Molds Stick|为什么玻璃钢新模具会粘模(上)

[复制链接]
发表于 2018-11-13 09:45:08 | 显示全部楼层 |阅读模式
本帖最后由 广东博皓公司 于 2018-11-13 09:52 编辑

嗨,大家好!博皓小编好久没出来晒晒太阳,吹吹水了!

虽然我们老大经常教导小编要低调做人,稳重做事,但闷得慌的小编还是忍不住跳出来班门弄斧一番!

今天广东博皓小编想跟各位小主探讨的是一个复合材料行业老生常谈的话题,那就是新模具为什么会容易粘模。算是把冷菜热一下,再端给各位小主品尝品尝。各位小主不喜勿喷啊!



话说1988-1989年间,美国玻璃纤维制造协会在进行工装和模具制造研讨会时,进行了一项有关模具粘模问题的调查。这项调查由524名从事玻璃钢模具工具操作的人完成。

Question: Have you ever stuck a mold on a plug?
Response: Almost 15% reported they had stuck a mold on a plug, at least one time.
问题:是否经历过模具被卡住脱不了模?
回答:近15%的人说他们至少有一次模具被卡住。

Question: Have you ever stuck a part in a new mold?
Response: Over 90% reported they had stuck parts in a new mold, at least one time.
问题:是否在新模具中遇到部件粘模问题?
回答:超过90%的人至少有一次在新模具上遇到部件粘模问题。



Question: Of all the molds you’ve built, how many have stuck one of the first three molded parts?
Response: About 13-15% of all initial parts stick in new molds.
问题:在你制作的所有模具中,前三个模制品有多少比例会粘到模具上?
回答:大约有13-15%的初始部位会粘在新模具上。
Question: What brand and type of mold release had been used on the molds that stuck?
Response:The brand and types of release agents were evenly distributed according to market share. All major mold release brands were reported to stick 13-15%(+/-1%) of new molds.
问题:粘模的时候,模具上使用了什么品牌和类型的脱模剂?
回答:根据市场份额,各种品牌和发行代理商都有粘模具情况。据报道,主要的脱模剂品牌有13-15%(+/-1%)的比例在新模具上会产生粘模问题。



The Smokeless Gun
One of the presuppositions of the survey was that certain types of mold releases would perform better than others. In closely examining the data it was found that 13-15% of ALL new molds stick, regardless of the type or brand of mold release used. All of the mold release types were reported to stick approximately the same number of new molds (within +/-1% of each other). The conclusion is that the type of mold release has very little bearing on mold sticking.
翻译:该调查的前提之一是,某些类型的脱模剂会比其他类型的产品性能更好。在仔细检查调查数据时发现,无论使用哪种类型或品牌的脱模剂,所有新模具都有13-15%的粘模几率。所有脱模剂类型都有相同的粘模概率 (误差在+/-1%之间)。结论是,脱模剂类型对模具的粘接影响很小。

以上是关于粘模的调查结果, 各位小主如果对调查结果有什么疑问,敬请在文章下方留言哦!

还有知道了新模具的确容易粘模,那么为什么会粘模呢?如何解决这类问题呢?

在下一篇文章里,小编将与各位一起一探究竟!

是不是很期待呢,请多关注博皓微信公众号,赶紧来抢沙发吧!

特别声明,本文章由博皓小编采集资料编辑(来自Boh.Lacovava)。
如想转载请注明转自广东博皓复合材料有限公司微信公众号。

--------------
产品/技术咨询:18026298689(赖先生)
客服电话:020-39966201
传真:020-39966209
地址:广东省广州市番禺区东环街番禺大道北555号天安节能科技园总部中心1号楼1103-1105室



回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册   扫一扫,用微信登录

本版积分规则

QQ|玻璃钢复合材料商城|联系我们|Archiver|手机版|小黑屋| FRP玻璃钢复合材料论坛 蜀ICP备10204395号-1

GMT+8, 2024-3-29 14:10 , Processed in 1.092129 second(s), 19 queries .

© 2015-2016

快速回复 返回顶部 返回列表